PLEASE READ THESE INSTRUCTIONS
CAREFULLY PRIOR TO INSTALLATION
Important Note: Please
inspect your spoiler for proper fit
before painting or mounting.
Parts which have been sanded,
painted, drilled, or modified cannot
be returned.
No-Drill Application STEP-by-STEP
| 1. |
Surface Cleaning
Clean surface area that
is to be covered by the
spoiler thoroughly with
Isopropyl Alcohol or lighter
fuel (available at a
convenience store or
supermarket) (See
Illustration 1). |
| 2. |
Test Fitting
Before removing the tape
backing, test fit the
spoiler in order to get
comfortable with the
placement. You can
mark the position with a
grease-free pen or masking
tape for a perfect fit (See
Illustration 2). |
| 3. |
Preparation
Peel back the corner of
the red liner on the 3M tape
and remove ALL pieces.
Avoid touching the exposed
tape (See Illustration 6). |
| 4. |
Installation
Gently press the spoiler
into place on the decklid,
hatch or glass. Once
satisfied with the
placement, firmly press down
on the spoiler to ensure
cohesion along the entire
vehicle's surface.
Continue to apply pressure
or use masking tape to keep
unit from lifting.
(See Illustrations 8 & 9). |
Helpful Tips
Adhesive silicones and/or
adhesion promoters are often
used in conjunction with the
provided 3M tape for long
lasting durability.
For best results,
installation should be
conducted in temperatures
above 72. Refer to
tape manufacturer's
recommendations for full
details. Do not clean,
wash, wax or drive for 12
hours after installation.
The manufacturer is not
responsible for no-drill
attachment durability. |
Drill Application STEP-by-STEP
Hardware Kit
Supplied in the box are one
spoiler & a plastic bag containing
the following:
| 1. |
Set of screws |
| 2. |
Set of locator strips |
Installation
| 1. |
Clean surface are that
is to be covered by spoiler
thoroughly with Isopropyl
Alcohol or lighter fuel
(available at convenience
stores or supermarkets) (See
Illustration 1). |
| 2. |
Before removing the tape
back, test fit the spoiler
in order to get comfortable
with the placement.
You can mark the position
with a grease-free pen or
masking tape for a perfect
fit (See Illustration 2). |
| 3. |
Insert the locator
strips into the mounting
holes. A small piece
of masking tape will hold
them temporarily in place
(See Illustration 3 &
Illustration 4). |
| 4. |
Set the spoiler in the
position you feel looks
best. You may want to
use a measuring tape to
insure you do have it
centered from side to side
and an equal distance on
each side from the back edge
of the decklid. |
| 5. |
Tape the locator strips
to the trunk lid on both
sides of the spoiler.
Carefully lift the spoiler
off the trunk lid leaving
the locator strips taped to
the decklid (See
Illustration 4). |
| 6. |
Drill through the center
of the locator strip (See
Illustration 5). |
| 7. |
Peel back the corner of
the red liner on the 3M
tape. Avoid touching
the exposed tape (See
Illustration 6). |
| 8. |
Tighten the screws
lightly to a depth of about
1/8" (about 2 screwdriver
turns), peel the tape
protecting the liner
completely and press the
spoiler gently onto the
trunk lid. |
| 9. |
Tight the screws firmly. |
Painting
*
IMPORTANT NOTICE FOR PAINTING YOUR
SPOILER
This spoiler is made of quality
CFC free polyurethane material.
If additional painting is needed for
a primered spoiler, please, use a
flexible agent.
 |
